fiestaturbo.com

[AW3K]

just the rears????

yeah the rear discs

[niracka]

Yea sorry mate I dont know I'v got drums on mine. I'l try n find out for you thaugh.

Ollie

[AW3K]

here is another bit closer

rs2k carriers, no washers needed , only bigger bolts



braided line



bout 5mm clearance on my 15inch rs7's



about 1mm clearance on my 14inch rs7's



plenty of room on the escort alloys





ordered some bits , hopfully getting them on sunday



Andy

[AW3K]

thanks to dave for these




hook end



as you can see the cable is too long, well maybe



so i may have to use these

[AW3K]

ended up getting the wrong cable (yoke and no adjusters) , so back it went , got right one this time

new cable has the correct end and adjuster



here we go, hub fitted



caliper fitted




line fitted , i ordered the custom made one but it looks like if you have a lowered car the originql one may reach from the car to the caliper

[knuckles]

nice progress andy.

[jonyb4]

looking good

if that braided line has a fair amount of slack, but as you say because its lowered, leave it on mate, mine failed the MOT due to when the car being raised on jacks the lines got to tight on the rear, and if it ever has its standard suspension put back on your gonna have issues

[AW3K]

these bad boys came today

20inc long with male and female ends oh yes £25 posted for the pair

top quality as well









its getting there

[jonyb4]

yay you can get cracking now

the race is on mate

20inc long with male and female ends oh yes

so i figure you could make them into a necklace if you wanted?

[AW3K]

yay you can get cracking now

the race is on mate

20inc long with male and female ends oh yes

so i figure you could make them into a necklace if you wanted?

lol somet like that, wanted them to connect to the goodridge ones i have so custom was needed

hurt my foot so cant do any more till it heals

Andy

[jonyb4]

yes! lol dont take this wrong but im in a delay also cant have you gaining on me lol

man flu's got me slowed

[AW3K]

lol a right pair lol

ill get it sorted

[AW3K]

the escort yoke has to be swapped for the fiesta one as it wont fit in the channel.



flexy hoses connected,



all set up baring the hand brake till i get other side on cos of the tension.



Andy

[jonyb4]

nice man, looks a bit liek spagetti junction but

shalt be long now

[AW3K]

gunna tie wrap the long one to handbrake cable when its fitted correctly

but if it works

Andy

[Minstral]

just a thouhgt andy but why didnt u just get some custom lines that ran from arch connector to the brake.

[AW3K]

just a thouhgt andy but why didnt u just get some custom lines that ran from arch connector to the brake.

the single long pipe i thought would have caught my wheels, this way i can tie it back

either way it works

[jonyb4]

well if it helps, the mk4/5's are as toby suggested, theyre chassis to hub lines, no rubbing issues

[rs-tom]

That pic is quality mate

how did fabio copello get in ur engine bay

[jonyb4]

haha

lol andy it looks like your photoshopped in

[AW3K]

lol every one says that im photoshopped but im not , i was trying to clen the cross member lol


little update

drivers side on and handbrake cable fitted, feels quite sharp

system needs bleeding but bat is dead so cant create a vacum




had to replace this part of the copper pipe as it wouldny come undone from the flexi




body kit back on on pass side



more to come

Andy

[jonyb4]

eek, the end is in sight

[AW3K]

its alive mwahhh

http://www.youtube.com/watch?v=uL-5FOR1glk

need some dot4 now then i can bleed the system

end is close

Andy

[jonyb4]

woot, lol you say end as its gonna be crushed or soemthing

the beginning!

andy i think you should deffo paint the rocker red! the standard greyish metal is

[AW3K]

woot, lol you say end as its gonna be crushed or soemthing

the beginning!

andy i think you should deffo paint the rocker red! the standard greyish metal is

yeah the end is close....


got new tyre's on alloy 195 / 45 / 15 and a 14" steelie with a 185 / 50 / 14 tire

bled brakes , secured the cable, fixed the fog light ....... booked mot tomoz at 4pm so got time to clean it before

Andy

[HCS PIMP]

andy have u got a new phone tried ringing you a few times recently to no prevail lol
you stil have the old faithful xr2i
i have a fez again as u may have noticed
this ones maybe going to last longer than the other 3 i hope

[AW3K]

andy have u got a new phone tried ringing you a few times recently to no prevail lol
you stil have the old faithful xr2i
i have a fez again as u may have noticed
this ones maybe going to last longer than the other 3 i hope

yeah still got same number, best bet is texting me as i cant answer calls much with work

hows youu?

car failed mot due to brake pedal spoungy and rear brake inoficant , needs adjusting

[jonyb4]

oopsy, but easy stuff

[HCS PIMP]

lol spongy brake pedal that will be a lovely bubble or could just be they need to bed in

[jonyb4]

i find that brakes and clutches sometimes need bleeding twice to be perfect

[niracka]

Yea you could ahve just had a bubble or two stuck in the master cylinder or something. I had to bleed mine twice last time to get it right

Glad to see her coming on anyways man. Be good to see you again soon. I'l drop you a line next time I'm up that way.

Ollie

[AW3K]

ollie no worries mate, will be good to see you

need to fit a mondeo master cylinder to componsate for the double sized front calipers and the 3/4 times larger rears, compared to the drums

[AW3K]

before



after




size differance , mondeo on left fiesta on right.



some pipe work has to be altered but not too bad

cant connect it all up till i get a new seal

Andy

[jonyb4]

looking good, should help push them stoppers now

[AW3K]

plumbed in now

handbrake adjusted as well