Guide - DIY Solid Engine Mounts

Please check here before posting to see if your question has been answered before.

Guide - DIY Solid Engine Mounts

Postby MattPym on Tue Jan 12, 2010 8:54 pm

Okay so i thought i would make a little guide for homemade solid engine mounts as i was doing this recently and took some pics. In essence this is just filling your engine mount with silicon so it becomes solid. This is ideal for the rear engine mount on Zetec engined fiestas as a solid replacement bushing is not commercially available. It also can act as a cheaper alternative to aftermarket engine mounts

This is a fairly simple procedure, nothing complicated. So here is a list of the things you will need/what i used.

- Engine mount
- Degreaser (Jizer)
- Permanent Marker
- Masking Tape
- Cardboard or Thin Plastic Sheet
- Scissors
- Silicon (I used Sikaflex 227)
- Silicon Gun
- Miscellaneous Bolt(s)
- Latex Gloves
- Stanley blade
- Lollipop stick

Okay so to begin i cleaned off my engine mount in a small basin of degreaser as it was fairly gummy and covered in oil and dust, after which i rinsed it and dried it off

Image

I then got a piece of cardboard and traced the outline of the mount onto the cardboard with the marker. I suggest that it might be better to use to thin plastic sheet as this wont peel off onto the silicon once it has dried like happened with mine.

Image

Next get your scissors and cut out the outline of the mount drawn on the cardboard. Trim it so it sits neatly against the engine mount

Image


Once you are happy with the your cutout secure it to the engine mount using the masking tape to seal up one side of the engine mount while leaving the other side open

Image

Image

Now if there are any threaded holes that are exposed on the inside of the engine mount, we need to cover this to prevent silicon getting in here. The best way to do this is to find a long bolt of the same thread and screw it all the way into the hole so it is completely covered. You can see in the pictures above that i used an old head bolt to fill a threaded hole in the mount

Now with your silicon gun you can start to pump the silicon into the mount. The aim here is to squeeze as much silicon in as possible leaving little or no air pockets.

Image

Image

Image

Now you have a bit of an option here, you can fill the mount so it is roughly level with the top of the mount casing (as shown above) or if you want to be neat you can keep filling with silicon so it is now protruding from the mount. From here you can either smooth the silicon level with a lollipop stick or you can leave it to dry and then trim it flush with the top of the casing using a stanley blade

I chose to overfill the mount and will trim it once cured full

Image

You will need to leave the engine mount to cure over a period of about 2-4 days. After this you can remove the cardboard backing, if there are any pockets or voids you can fill these is with some more silicon and then allow to cure for another couple days.

As i said before, cardboard is not the best choice for the backing and you can see why here. This will be trimmed off with a stanley blade! Also you can see that the silicone did not fill the mount completely so i will have to pump some more silicon onto this to finish it

Image

Image

Once fully cured you can then remove any bolts protecting threaded holes and then install the engine mount into your car

After this all you have to do is sit back and feel the vibrations

This guide is not a definitive bible, but should give you a good idea of one of the possible ways of making your own solid engine mounts. This method should be able to be used on most engine mounts but not all

If anyone has any suggestions or tips you would like to add in, just let me know

Cheers
Matt
Image

I have parts for sale!!!!.....Nice parts too!!!
http://www.fiestaturbo.com/forums/lots-of-parts-for-sale-vt185591/
MattPym
Elite Post Master
Elite Post Master
 
Posts: 1294
Joined: Mon Oct 16, 2006 10:11 am
Location: Galway, Ireland Drives: RS1800

Re: Guide - DIY Solid Engine Mounts

Postby Ruishy1 on Tue Jan 12, 2010 9:36 pm

nice guide mate, rather than sikaflex i used tiger seal its more rigid :)
Image
Ruishy1
Elite Post Master
Elite Post Master
 
Posts: 4006
Joined: Thu Mar 25, 2004 8:43 pm
Location: Sunny Kilmarnock

Re: Guide - DIY Solid Engine Mounts

Postby Smo on Wed Jan 13, 2010 12:37 am

Good work :)

As you suggest, I imagine it'll cause at least 'some' vibrations, but if that doesn't bother people, it should do the job!

I think I have an old mount I might try this with, although I really want to remove some of the vibrations I already have, so probably not the best idea :lol: But I reckon it's worth a go to see what it's like :D
Image
Smo
Elite Post Master
Elite Post Master
User avatar
Posts: 8658
Joined: Sun Dec 29, 2002 12:33 am
Location: My indecisive mind, in Thanet, Kent.

Car: 1990 Ford Fiesta Popular Plus

Re: Guide - DIY Solid Engine Mounts

Postby Ruishy1 on Wed Jan 13, 2010 3:23 am

If you dont want them too solid, only use some sealant, and some of the original rubber mount.
Image
Ruishy1
Elite Post Master
Elite Post Master
 
Posts: 4006
Joined: Thu Mar 25, 2004 8:43 pm
Location: Sunny Kilmarnock

Re: Guide - DIY Solid Engine Mounts

Postby dug112y on Mon Feb 01, 2010 12:01 am

grease your card/plastic so it dont stick
dug112y
Newbie Poster
Newbie Poster
 
Posts: 12
Joined: Thu Dec 11, 2008 2:22 am

Re: Guide - DIY Solid Engine Mounts

Postby John_D on Fri Mar 05, 2010 8:18 pm

can i ask a stupid question, why would you do this? is there some benefit to the engine not moving?
John_D
Elite Post Master
Elite Post Master
 
Posts: 1007
Joined: Sat Nov 12, 2005 7:09 pm
Location: Fife

Re: Guide - DIY Solid Engine Mounts

Postby Ruishy1 on Sun Mar 07, 2010 6:10 pm

from what i understand it transmits more bhp/torque to the wheels instead of being lost in flex, i could be wrong though :)
Ruishy1
Elite Post Master
Elite Post Master
 
Posts: 4006
Joined: Thu Mar 25, 2004 8:43 pm
Location: Sunny Kilmarnock

Re: Guide - DIY Solid Engine Mounts

Postby jonboisescort on Sun Mar 07, 2010 6:23 pm

i used an old exhaust rubber and cut it up and pushed it into the gaps

worked a treat :) lol
jonboisescort
Elite Post Master
Elite Post Master
User avatar
Posts: 2055
Joined: Mon Jun 11, 2007 1:48 pm
Location: christchurch dorset

Car: 1994 Ford Fiesta

Re: Guide - DIY Solid Engine Mounts

Postby John_D on Sun Mar 07, 2010 7:15 pm

[quote="jonboisescort"]i used an old exhaust rubber and cut it up and pushed it into the gaps

worked a treat :) lol[/quote]

working on a budget, i lke it :)
John_D
Elite Post Master
Elite Post Master
 
Posts: 1007
Joined: Sat Nov 12, 2005 7:09 pm
Location: Fife

Re: Guide - DIY Solid Engine Mounts

Postby russ-RST on Sat Apr 17, 2010 9:07 am

[quote="jonboisescort"]i used an old exhaust rubber and cut it up and pushed it into the gaps

worked a treat :) lol[/quote]

good idea :D im liking the sound of this i think when i do my conversion i 'l do this to the mount as im not bothered how rough the ride is as long as im going past people lol
russ-RST
Elite Post Master
Elite Post Master
 
Posts: 1438
Joined: Thu Apr 01, 2010 11:05 am
Location: margate kent
Your car: fiesta rs turbo

Re: Guide - DIY Solid Engine Mounts

Postby Excursion on Tue Apr 27, 2010 1:43 pm

Great idea :)
Excursion
Bulletin Board User
Bulletin Board User
User avatar
Posts: 15228
Joined: Thu Jan 01, 1970 1:00 am
Location: Skynet
Your car: Ford Fiesta

Car: 1990 Ford Fiesta XR2i

Re: Guide - DIY Solid Engine Mounts

Postby MK4 Rick on Sun Jan 12, 2014 3:02 pm

Its a bloody good idea a lot of people reckon its a bodge lol.
MK4 Rick
Elite Post Master
Elite Post Master
 
Posts: 1571
Joined: Fri Jan 28, 2005 12:51 pm
Location: Manchester
Your car: Mk5 Fiesta


Twitter

The second 20th Anniversary article, a dive into the history of how the site came about is available here: https://t.co/kbCfZ4sf0R

17:44, 4th December 2021 Twitter Web App

To celebrate https://t.co/wXVkvJipaS being 20 years old this year, I've written a series of articles detailing the… https://t.co/B0vE0Y3KvP

17:42, 4th December 2021 Twitter Web App

Follow fiestaturbo.com on Twitter:
http://twitter.com/fiestaturbo/

RSS Feeds

Subscribe to the RSS feed

What is RSS?

RSS is a technology that lets you use special applications or modern browsers to notify you you when a site is updated. You can then read the updated content in that application or your browser.

To subscribe to these RSS feeds you need to copy the links above. For instructions on how to add it to the feeds you keep track of, consult the documentation of your RSS reader.