Moondust K-Reg MK3 2.3 Duratec-HE Turbo. SOLD on 26/06/2011

Post pics of your Fiesta here.

Re: Silver K-Reg 2.3 Duratec-Turbo: 07/10/08

Postby jimmyesh on Wed Oct 08, 2008 2:47 pm

Project_XR2i_Trackcar wrote:Welcome back Jim

Doesn't seem like a few days ago we were sipping coffee in Bastion. Have you spent your op bonus yet?


Hi Chris, cheers mate. Yeah spent some of it - see this thread to see where it went! :Q

Was good meeting up in Afghan - I'll bet that it's the first time there's ever been a FT.Com gathering (well, 2 of us anyway) in Afghanistan! :lol:

Today's visit to G & L Autospares yielded the following (For just £30!! :aviator: ):

Fiesta MK3.5 Si steering column.

Fiesta MK3.5 Si Power steeing Rack and track rods.

Fiesta MK3.5 Si Power steering pipework

Fiesta MK5 Zetec S Power steering L/P pipework with cooler.

Mondeo MK3 2.0 Duratec Power Steering H/P pipework (will be taken to hose specialist and a hybrid pipe made with the pump-end of this one and the rack-end of the Fez Si hose)

Mondeo MK3 2.0 Duratec Fuel Rail Inlet pipe.

Mondeo MK3 2.0 Duratec Alternator/Starter Motor wiring.

Mondeo mk3 2.0 Duratec bolts for engine/bellhousing, alternator, starter motor, P/steeing pump.

Mondeo mk3 2.0 Duratec Vehicle Speed Sensor.

Image

Although these bits were dirt-cheap, removing the steering rack from a ground-mounted Fiesta Si that still had the engine fitted was "sporting" to say the least! :aaah: Needless to say I was there for a fair old while today and left in a knackered state! :lol:
Last edited by jimmyesh on Tue Mar 23, 2010 2:31 pm, edited 1 time in total.
jimmyesh
Elite Post Master
Elite Post Master
 
Posts: 1988
Joined: Fri Oct 20, 2006 3:25 pm
Your car: Yes

Re: Silver K-Reg 2.3 Duratec-Turbo: 07/10/08

Postby Project_XR2i_Trackcar on Wed Oct 08, 2008 4:19 pm

jimmyesh wrote:
Was good meeting up in Afghan - I'll bet that it's the first time there's ever been a FT.Com gathering (well, 2 of us anyway) in Afghanistan! :lol:



and dare i say it the one and only :D

bloody bargain there matey, rack alone would have cost more than that on an exchange
Image

Renault Sport Megane 250 Cup
Ford Fiesta XR2i 2.0 trackcar
Project_XR2i_Trackcar
Elite Post Master
Elite Post Master
 
Posts: 2947
Joined: Thu Apr 22, 2004 10:58 pm
Location: Melton mowbray
Your car: Xr2i

Re: Silver K-Reg 2.3 Duratec-Turbo: 08/10/08

Postby White2i on Wed Oct 08, 2008 7:17 pm

some bargins there mate i just cheat i got a xr2i i slowly been pinching the bits of in my back garden

looking good thought u nearly got all the bits you need yet?
White2i
Post Master
Post Master
 
Posts: 994
Joined: Tue Apr 25, 2006 11:31 am
Location: ipswich

Re: Silver K-Reg 2.3 Duratec-Turbo: 08/10/08

Postby jimmyesh on Wed Oct 08, 2008 8:07 pm

White2i wrote: u nearly got all the bits you need yet?



Yeah not far off - got enough to get everything "thrown in the hole" so to speak. Gonna crack on with making everything fit / weld engine/trans mounting points etc once I collect the car and engine. That'll buy me some time to save a bit for fuel system components, Omex 710 or 600, Samco hoses, exhaust system and Quaife ATB diff.


If anyone wants an XR2i CVH EFi Engine (runs quietly but could do with a freshen-up), XR2i 'Box complete with driveshafts and linkage etc, full XR2i CHV loom & ECU, all mounts and a Scorpion Exhaust tail with standard centre-section. Just give me a shout - I'm putting it all on ebay soon anyway :wink:
jimmyesh
Elite Post Master
Elite Post Master
 
Posts: 1988
Joined: Fri Oct 20, 2006 3:25 pm
Your car: Yes

Re: Silver K-Reg 2.3 Duratec-Turbo: 08/10/08

Postby filtra on Wed Oct 08, 2008 8:28 pm

LOL, good effort man, it's all about the moment when you roll onto your back with a cut up hand, aching arm, dripping sweat everywhere with that baxtered part finally out!

Looking forward to the progress on this!
Ex Fiesta RS Turbo owner :(
filtra
Elite Post Master
Elite Post Master
User avatar
Posts: 2029
Joined: Fri Jul 09, 2004 10:15 am
Location: Kingston, Surrey

Car: 1991 Ford Fiesta RS Turbo

Re: Silver K-Reg 2.3 Duratec-Turbo: 08/10/08

Postby White2i on Wed Oct 08, 2008 8:44 pm

if you need a hand mate you will have to shout and also if you need somethings making then shout i am a metal fabricator so can get bits knocked up at work lol on the quiet

sounds like you need to get car and engine asap then so you can get cracking
White2i
Post Master
Post Master
 
Posts: 994
Joined: Tue Apr 25, 2006 11:31 am
Location: ipswich

Re: Silver K-Reg 2.3 Duratec-Turbo: 08/10/08

Postby jimmyesh on Wed Oct 08, 2008 8:58 pm

Feersum_Enjin wrote:LOL, good effort man, it's all about the moment when you roll onto your back with a cut up hand, aching arm, dripping sweat everywhere with that baxtered part finally out!

Looking forward to the progress on this!



Cheers Feersum :) I've been in the state you mentioned there on a few occasions :aaah: My scrap-yard visits this week have served as build-up training in preparation for some serious spannering to begin! :devil:

White2i wrote:if you need a hand mate you will have to shout and also if you need somethings making then shout i am a metal fabricator so can get bits knocked up at work lol on the quiet

sounds like you need to get car and engine asap then so you can get cracking


Cheers Marc, I'll be in touch should I be needing a hand mate :) Yeah need to get cracking but family comes first - I've hardly seen my wife and kids the last few months so when my leave starts properly I'll be spending as much time as I can with them. Once they've done my head in I'll turn my attention to the car! :P
jimmyesh
Elite Post Master
Elite Post Master
 
Posts: 1988
Joined: Fri Oct 20, 2006 3:25 pm
Your car: Yes

Re: Silver K-Reg 2.3 Duratec-Turbo: 08/10/08

Postby White2i on Wed Oct 08, 2008 9:11 pm

yea thats understandable mate, so will be a week or so before you get round to it then lol
White2i
Post Master
Post Master
 
Posts: 994
Joined: Tue Apr 25, 2006 11:31 am
Location: ipswich

Re: Silver K-Reg 2.3 Duratec-Turbo: 08/10/08

Postby disc on Thu Oct 09, 2008 9:17 pm

Does Mondeo mk3 2.0 Duratec Vehicle Speed Sensor fits in old gearboxes?
Can you post pic of it?
Thanks!
Sorry for my bad english...
Image
disc
Senior Poster
Senior Poster
 
Posts: 239
Joined: Fri Feb 06, 2004 8:03 pm
Location: Bulgaria
Your car: 1991 Orion ZetecTurbo 270BHP

Re: Silver K-Reg 2.3 Duratec-Turbo: 08/10/08

Postby jimmyesh on Fri Oct 10, 2008 10:37 am

disc wrote:Does Mondeo mk3 2.0 Duratec Vehicle Speed Sensor fits in old gearboxes?
Can you post pic of it?
Thanks!



Here you go - even got my hands dirty for you! :bonkers:

Image

The white blanking-plate on the left is what my late-MK3 Mondeo MTX75 'box was fitted with (they must use some other means of speed measurement, wheel speed etc...) On the right you can see I have fitted the early-MK3 Mondeo Vehicle Speed Sensor (VSS) in its place - This sensor is the same one that 5-speed MTX 'boxed Focus models (2-litre & RS) used too.

When you say "old gearboxes", which type do you mean? :-? The small-engined Focus (1.4,1.6, maybe 1.8) came with the B5(BC-type) gearbox as shared by Pumas, Fiestas MK2-MK6 and therefore the Focus and late Fiesta should have some form of VSS fitted into the 'box too. If you mean older variants of the MTX75, the XR3i 130, MK5 & 6 RS2000, Mondeo MK1,2, Cougar, Probe were all fitted with this 'box over the years.

Hope that helps mate :)
Last edited by jimmyesh on Tue Mar 23, 2010 2:33 pm, edited 1 time in total.
jimmyesh
Elite Post Master
Elite Post Master
 
Posts: 1988
Joined: Fri Oct 20, 2006 3:25 pm
Your car: Yes

Re: Silver K-Reg 2.3 Duratec-Turbo: 08/10/08

Postby jimmyesh on Fri Oct 10, 2008 5:20 pm

Got a nice surprise in the post today.... A Turbo! :D Garrett GT28R Ball-Bearing to be precise, should be just what my car needs for a nice bit of poke but (hopefully) next to no lag - 2.3 Litres & 9:1 Comp should see to that! :devil:

Image

Image

Wasn't brand-new but has hardly been used either, as the seller was upgrading to something that would give him 400+BHP. There is no play in the shaft and everything looks spot-on so hopefully it'll produce the goods.

Here's a pic of my manifold that I've ordered from Pumaspeed (still waiting for it...), not cheap but is a good quality cast item that is also pretty compact. Although it doesn't have equal-length header it should still more than suffice for my power needs (people have extracted silly power on RST's using the standard manifold which is of a similar design to this :) )

Image

Also took a bimble to Colchester Machine Mart today and purchased the obligatory £38 engine stand. :)
Last edited by jimmyesh on Tue Mar 23, 2010 2:35 pm, edited 1 time in total.
jimmyesh
Elite Post Master
Elite Post Master
 
Posts: 1988
Joined: Fri Oct 20, 2006 3:25 pm
Your car: Yes

Re: MK3 2.3 Duratec-Turbo: 10th Oct 2008 Turbo & Manifold!

Postby White2i on Fri Oct 10, 2008 11:45 pm

looking good mate what power you expecting from that set up then mate 300+?
White2i
Post Master
Post Master
 
Posts: 994
Joined: Tue Apr 25, 2006 11:31 am
Location: ipswich

Re: MK3 2.3 Duratec-Turbo: 10th Oct 2008 Turbo & Manifold!

Postby jimmyesh on Sat Oct 11, 2008 8:39 am

White2i wrote:looking good mate what power you expecting from that set up then mate 300+?


Around 300 BHP will be fine, a 2.3 producing 300 BHP is the same as a 1.6 producing 200 BHP or so, as far as how much stress the engine is under goes. So hopefully it'll be strong and reliable and have an abundance of torque due to the relatively large displacement :devil:
Last edited by jimmyesh on Tue Mar 23, 2010 2:37 pm, edited 1 time in total.
jimmyesh
Elite Post Master
Elite Post Master
 
Posts: 1988
Joined: Fri Oct 20, 2006 3:25 pm
Your car: Yes

Re: MK3 2.3 Duratec-Turbo: 10th Oct 2008 Turbo & Manifold!

Postby jmeBDC on Sat Oct 11, 2008 10:50 am

Amazing project! Cant wait to see it all come together.
Image
jmeBDC
Poster
Poster
 
Posts: 95
Joined: Thu Oct 09, 2008 11:02 am
Location: South Essex & East Coast Kent

Re: MK3 2.3 Duratec-Turbo: 10th Oct 2008 Turbo & Manifold!

Postby Ruishy1 on Sat Oct 11, 2008 1:24 pm

with the capacity, turbo and compression ratio, i cant wait to see the torque curve :Q

well done for doing something different mate, the world needs more people like you to break the mould :D
Image
Ruishy1
Elite Post Master
Elite Post Master
 
Posts: 4006
Joined: Thu Mar 25, 2004 8:43 pm
Location: Sunny Kilmarnock

Re: MK3 2.3 Duratec-Turbo: 10th Oct 2008 Turbo & Manifold!

Postby FRSJON on Sat Oct 11, 2008 3:00 pm

the parts are coming thick and fast mate.... :o ... just need the time to fit it all together.... :Q
Image
FRSJON
Elite Post Master
Elite Post Master
User avatar
Posts: 4662
Joined: Mon Oct 30, 2006 10:26 pm
Location: ISLE OF WIGHT
Your car: frozen white/carbon zt

Re: MK3 2.3 Duratec-Turbo: 10th Oct 2008 Turbo & Manifold!

Postby filtra on Sat Oct 11, 2008 8:29 pm

Nice spec! Those extra 300cc's should spool the turbo up nicely! I take it the standard exahust housing won't be restricting at high revs?
Ex Fiesta RS Turbo owner :(
filtra
Elite Post Master
Elite Post Master
User avatar
Posts: 2029
Joined: Fri Jul 09, 2004 10:15 am
Location: Kingston, Surrey

Car: 1991 Ford Fiesta RS Turbo

Re: MK3 2.3 Duratec-Turbo: 10th Oct 2008 Turbo & Manifold!

Postby jimmyesh on Sat Oct 11, 2008 8:53 pm

Feersum_Enjin wrote:Nice spec! Those extra 300cc's should spool the turbo up nicely! I take it the standard exahust housing won't be restricting at high revs?


I hope not mate - I'll just have to try it as it is then iron out any problems as/when they arise :oooh:

Just been on the Earls Hoses website to sort out some steel -6AN Male fittings to be welded to each end of my fuel-rail. As standard it just has a single push-fit fuel feed and no return line, I want to keep the standard fuel tank set up and lines so am converting it to run a return line, along with a nice Sytec fuel pressure regulator with -6 fittings and aeroquip hoses.
jimmyesh
Elite Post Master
Elite Post Master
 
Posts: 1988
Joined: Fri Oct 20, 2006 3:25 pm
Your car: Yes

Re: MK3 2.3 Duratec-Turbo: 10th Oct 2008 Turbo & Manifold!

Postby adie_mwell on Mon Oct 13, 2008 1:01 am

you dont hang about with you project do you jim :P
Image

Fiesta 1.8 ZVH
Fiesta 2.1 Zetec Turbo In The Making
Fiesta YB Cosworth In The Making

Fuk The DVLA ! Mon The Fords
adie_mwell
Senior Poster
Senior Poster
 
Posts: 313
Joined: Sun Mar 11, 2007 7:42 pm
Location: Motherwell , Scotland

Re: MK3 2.3 Duratec-Turbo: 10th Oct 2008 Turbo & Manifold!

Postby heeman10 on Mon Oct 13, 2008 3:59 pm

Nice safe manifold there :) Loving the efficient compressor outlet too! :aaah: :lol:

That engine will need bugggger all boost to make 300bhp, as you undoubtedly know already. Tis the way forward :)
Image
James .:. 193bhp/245lbft Zetec Turbo Mk3. Click sig for conversion thread + videos .:.
heeman10
Elite Post Master
Elite Post Master
User avatar
Posts: 28746
Joined: Fri Nov 08, 2002 5:32 pm
Location: Somerset
Your car: Audi TT TDI Quattro S line

Re: MK3 2.3 Duratec-Turbo: 10th Oct 2008 Turbo & Manifold!

Postby jimmyesh on Mon Oct 13, 2008 4:40 pm

heeman10 wrote:Nice safe manifold there :) Loving the efficient compressor outlet too! :aaah: :lol:

That engine will need bugggger all boost to make 300bhp, as you undoubtedly know already. Tis the way forward :)


Hi James haven't heard from you for a while mate, hope all is well :wink:

Yeah the compressor outlet and other gubbins is for a Nissan 200sx so I'll probably be binning it (definitely after your piss-taking! :bonkers: ).

You're right mate - "no substitute for cubes" and all that, especially when an alloy 2.3 4-pot weighs the same or less than a 1.6CVH! :Q
jimmyesh
Elite Post Master
Elite Post Master
 
Posts: 1988
Joined: Fri Oct 20, 2006 3:25 pm
Your car: Yes

Re: MK3 2.3 Duratec-Turbo: 10th Oct 2008 Turbo & Manifold!

Postby rob pace on Tue Oct 14, 2008 5:27 pm

nice project i must say!

good to meet you as well, hope the exhaust is what you were looking for :D
Image
rob pace
Elite Post Master
Elite Post Master
 
Posts: 4702
Joined: Fri May 06, 2005 2:10 pm
Location: west wickham, kent

Re: MK3 2.3 Duratec-Turbo: 10th Oct 2008 Turbo & Manifold!

Postby dontpannic on Tue Oct 14, 2008 5:52 pm

This'll be a brilliant project. Keeping my eyes peeled on this one seeing how much of a success the MANJ was! :D
Image
dontpannic
Elite Post Master
Elite Post Master
User avatar
Posts: 7244
Joined: Thu Mar 16, 2006 5:21 pm
Location: Orpington, Kent
Your car: Fiesta ST / Saxo VTS track car

Car: 2007 Ford Fiesta ST

Re: MK3 2.3 Duratec-Turbo: 10th Oct 2008 Turbo & Manifold!

Postby jimmyesh on Thu Oct 16, 2008 10:39 am

rob pace wrote:nice project i must say!

good to meet you as well, hope the exhaust is what you were looking for :D


The exhaust is perfect cheers Rob, should sound lovely with my beast of an engine howling through it! :devil: That FRST of yours is a stunning car too :Q

Didn't get back to Colchester until 8:30pm after going to Sittingbourne to pick the engine up from my mate's house :aaah:
jimmyesh
Elite Post Master
Elite Post Master
 
Posts: 1988
Joined: Fri Oct 20, 2006 3:25 pm
Your car: Yes

Re: MK3 2.3 Duratec-Turbo: 10th Oct 2008 Turbo & Manifold!

Postby jimmyesh on Thu Oct 16, 2008 1:02 pm

We have progress!! :Q

Ancillaries all stripped from the engine and it's now mounted on the stand ready for stripdown and re-bore.


Image

Image

The other day I moved all my car parts for this project into a secure locker at work - This allowed me to sleep better at night as previously, they were all stashed in my rickety shed begging to be stolen! :aaah:

Image

When I get some more "quiet time" at work I'll strip the engine down and get the block off to Cober Engineering in Colchester.
Last edited by jimmyesh on Tue Mar 23, 2010 2:40 pm, edited 2 times in total.
jimmyesh
Elite Post Master
Elite Post Master
 
Posts: 1988
Joined: Fri Oct 20, 2006 3:25 pm
Your car: Yes

Re: MK3 2.3 Duratec-Turbo: FRI 17th Oct 2008 Engine Stripdown

Postby jimmyesh on Fri Oct 17, 2008 6:25 pm

Obviously yesterday's update wasn't interesting enough for you all! :rolleyes: :lol:

Well here's what was achieved this morning... May be of interest for anyone who wishes to see the innards of the rather strange engine that is the Ford/Mazda Duratec 2.3 :)

Pro Alloy full-width Rad & GRS Intercooler collected from DHL depot.

Image

Engine Stripdown - Duratec has a cover over the timing chain which needs removing first.

Image

See, cam chain NOT cam belt, bit different to the Zetec eh?

Image

Cams need removing to enable head removal.

Image

Cam Bearing-Caps all labelled using good old Army Issue Mine-Tape :D

Image

Oil Pump chain and pump need removing prior to block machining.

Image

Ready for Head removal.

Image

Head Removed

Image

Image

Here's the crank setup - note the balance-shaft mechanism that is specific to the 2.3 (due to its longer stroke) - Driven at 2 x Crank speed by a gear on the Crank (see pics) can be removed though and I may just do that as it's a heavy old thing! Just need to research a few yank forums and see how harsh the engine is without it...

Image

Image

Image

The crank on the Duratec is carried high in the block in a cradle which incorporates all the main caps.

Image

Crank with cradle removed.

Image

Bare Block at last!

Image

Off to Cober Precision Engineering, collecting it middle of next week all freshly bored to 88mm for me to rebuild :Q bloody light too, you can easily carry it with one hand! :o

Image
Last edited by jimmyesh on Tue Mar 23, 2010 2:42 pm, edited 1 time in total.
jimmyesh
Elite Post Master
Elite Post Master
 
Posts: 1988
Joined: Fri Oct 20, 2006 3:25 pm
Your car: Yes

Re: MK3 2.3 Duratec-Turbo: FRI 17th Oct 2008 Engine Stripdown

Postby jayrs on Fri Oct 17, 2008 7:45 pm

looking good mate, and thats one weird crank set up :lol: :lol: , when you reckon engine will be back together ready for fitting?
jayrs
Elite Post Master
Elite Post Master
User avatar
Posts: 31520
Joined: Mon Apr 19, 2004 10:32 pm
Location: I.O.W
Your car: FRST, XR2, ST170, ST225

Car: 1991 Ford Fiesta RS Turbo

Re: MK3 2.3 Duratec-Turbo: FRI 17th Oct 2008 Engine Stripdown

Postby jimmyesh on Fri Oct 17, 2008 7:57 pm

jayrs wrote:looking good mate, and thats one weird crank set up :lol: :lol: , when you reckon engine will be back together ready for fitting?


Engine should be assembled within the next week (dependant on my Cosworth gaskets arriving from Burton Power - they had to order them in. Also still waiting on my ARP main and head studs from the states, should hopefully be here this week...).

As for it all being fitted "in the hole" I'll stick my neck out and say "by January" but that's barring any serious setbacks and/or wife losing the plot with me!! :rolleyes: :lol:
jimmyesh
Elite Post Master
Elite Post Master
 
Posts: 1988
Joined: Fri Oct 20, 2006 3:25 pm
Your car: Yes

Re: MK3 2.3 Duratec-Turbo: FRI 17th Oct 2008 Engine Stripdown

Postby jayrs on Fri Oct 17, 2008 8:12 pm

lolo, fair enough mate, is that a time limit like something i put on my rs of er, 6 months :lol: :lol: :lol:
jayrs
Elite Post Master
Elite Post Master
User avatar
Posts: 31520
Joined: Mon Apr 19, 2004 10:32 pm
Location: I.O.W
Your car: FRST, XR2, ST170, ST225

Car: 1991 Ford Fiesta RS Turbo

Re: MK3 2.3 Duratec-Turbo: FRI 17th Oct 2008 Engine Stripdown

Postby LeePFRST on Fri Oct 17, 2008 8:29 pm

Coming along well mate, looks like you've got your work cut out between now and January then! :lol:
Escort GTI Turbo
LeePFRST
Post Master
Post Master
User avatar
Posts: 647
Joined: Sat Sep 27, 2003 2:25 pm
Location: Essex

Car: 1990 Ford Fiesta RS Turbo

Re: MK3 2.3 Duratec-Turbo: FRI 17th Oct 2008 Engine Stripdown

Postby jimmyesh on Fri Oct 17, 2008 8:58 pm

LeePFRST wrote:Coming along well mate, looks like you've got your work cut out between now and January then! :lol:



Lol I love a bit of graft! :lol: :Q
jimmyesh
Elite Post Master
Elite Post Master
 
Posts: 1988
Joined: Fri Oct 20, 2006 3:25 pm
Your car: Yes

Re: MK3 2.3 Duratec-Turbo: FRI 17th Oct 2008 Engine Stripdown

Postby FRSJON on Fri Oct 17, 2008 9:04 pm

engine looks in really good condition mate.... :) ... all coming along quickly too...nice one... :Q
Image
FRSJON
Elite Post Master
Elite Post Master
User avatar
Posts: 4662
Joined: Mon Oct 30, 2006 10:26 pm
Location: ISLE OF WIGHT
Your car: frozen white/carbon zt

Re: MK3 2.3 Duratec-Turbo: FRI 17th Oct 2008 Engine Stripdown

Postby White2i on Fri Oct 17, 2008 9:07 pm

looking good mate, some good progress there, you will have engine back together no problems then if rest of bits turn up, i cant wait to see this all done and finished :) :Q
White2i
Post Master
Post Master
 
Posts: 994
Joined: Tue Apr 25, 2006 11:31 am
Location: ipswich

Re: MK3 2.3 Duratec-Turbo: FRI 17th Oct 2008 Engine Stripdown

Postby Ruishy1 on Fri Oct 17, 2008 10:17 pm

fan-bloody-tastic is all i can say :Q
Image
Ruishy1
Elite Post Master
Elite Post Master
 
Posts: 4006
Joined: Thu Mar 25, 2004 8:43 pm
Location: Sunny Kilmarnock

Re: MK3 2.3 Duratec-Turbo: FRI 17th Oct 2008 Engine Stripdown

Postby paulgrs2 on Sat Oct 18, 2008 10:33 am

Well done Jim on another stunning project, you sure your not a VM lol.
Just to get things straight in my head, is the bolt patten for the duratec (proper) different to the zetec/I4 etc as there seems to be alot of differant opinion on different websites, basically will a mtx75 gearbox (my only option due to needing 4x4) bolt on?

What boost you planning on running with a 9:1 compression ratio, surely running this high you have limited it to not alot huh? But there again I suppose you need to keep the power sensible to keep control of the torque steer.

How come your going Omex management? :)
paulgrs2
Newbie Poster
Newbie Poster
 
Posts: 9
Joined: Sun Feb 18, 2007 8:59 am

PreviousNext

cron

Twitter

The second 20th Anniversary article, a dive into the history of how the site came about is available here: https://t.co/kbCfZ4sf0R

17:44, 4th December 2021 Twitter Web App

To celebrate https://t.co/wXVkvJipaS being 20 years old this year, I've written a series of articles detailing the… https://t.co/B0vE0Y3KvP

17:42, 4th December 2021 Twitter Web App

Follow fiestaturbo.com on Twitter:
http://twitter.com/fiestaturbo/

RSS Feeds

Subscribe to the RSS feed

What is RSS?

RSS is a technology that lets you use special applications or modern browsers to notify you you when a site is updated. You can then read the updated content in that application or your browser.

To subscribe to these RSS feeds you need to copy the links above. For instructions on how to add it to the feeds you keep track of, consult the documentation of your RSS reader.